- parametric-filter Amplifiers
- parametric-filter Audio
- parametric-filter Battery management ICs
- parametric-filter
- parametric-filter DLP products
- parametric-filter Data converters
- parametric-filter
- parametric-filter Interface
- parametric-filter Isolation
- parametric-filter
- parametric-filter
- parametric-filter Motor drivers
- parametric-filter Power management
- parametric-filter
- parametric-filter Sensors
- parametric-filter
- parametric-filter Wireless connectivity
- parametric-filter Application-specific port protection ICs
- parametric-filter CAN transceivers
- parametric-filter Diodes
- parametric-filter Ethernet ICs
- parametric-filter
- parametric-filter High-speed SerDes
- parametric-filter
- parametric-filter
- parametric-filter LIN transceivers
- parametric-filter
- parametric-filter Multi-switch detection interface (MSDI) ICs
- parametric-filter Optical networking ICs
- parametric-filter Other interfaces
- parametric-filter
- parametric-filter
- parametric-filter RS-232 transceivers
- parametric-filter
- parametric-filter Serial digital interface (SDI) ICs
- parametric-filter System basis chips (SBCs)
- parametric-filter UARTs
- parametric-filter USB ICs
Home
Interface
Quadruple Differential Line Receiver
Data sheet
- document-pdfAcrobat SNx5175 Quadruple Differential Line Receivers datasheet (Rev. D) PDF | HTML
Product details
- Meet or exceed the requirements of ANSI standard EIA/TIA-422-B, RS-423-B, and RS-485
- Meet ITU recommendations V.10, V.11, X.26, and X.27
- Designed for multipoint bus transmission on long bus lines in noisy environments
- 3-state outputs
- Common-mode input voltage range: −12 V to 12 V
- Input sensitivity: ±200 mV
- Input hysteresis: 50-mV typical
- High input impedance: 12-kΩ minimum
- Operate from single 5-V supply
- Low-power requirements
- Plug-in replacement for MC3486
- Meet or exceed the requirements of ANSI standard EIA/TIA-422-B, RS-423-B, and RS-485
- Meet ITU recommendations V.10, V.11, X.26, and X.27
- Designed for multipoint bus transmission on long bus lines in noisy environments
- 3-state outputs
- Common-mode input voltage range: −12 V to 12 V
- Input sensitivity: ±200 mV
- Input hysteresis: 50-mV typical
- High input impedance: 12-kΩ minimum
- Operate from single 5-V supply
- Low-power requirements
- Plug-in replacement for MC3486
The SN65175 and SN75175 are monolithic quadruple differential line receivers with 3-state outputs. They are designed to meet the requirements of ANSI Standards EIA/TIA-422-B, RS-423-B, and RS-485, and several ITU recommendations. These standards are for balanced multipoint bus transmission at rates up to 10 megabits per second. Each of the two pairs of receivers has a common active-high enable.
The receivers feature high input impedance, input hysteresis for increased noise immunity, and input sensitivity of ±200 mV over a common-mode input voltage range of ±12 V. The SN65175 and SN75175 are designed for optimum performance when used with the SN75172 or SN75174 quadruple differential line drivers.
The SN65175 is characterized for operation from −40°C to 85°C. The SN75175 is characterized for operation from 0°C to 70°C.
The SN65175 and SN75175 are monolithic quadruple differential line receivers with 3-state outputs. They are designed to meet the requirements of ANSI Standards EIA/TIA-422-B, RS-423-B, and RS-485, and several ITU recommendations. These standards are for balanced multipoint bus transmission at rates up to 10 megabits per second. Each of the two pairs of receivers has a common active-high enable.
The receivers feature high input impedance, input hysteresis for increased noise immunity, and input sensitivity of ±200 mV over a common-mode input voltage range of ±12 V. The SN65175 and SN75175 are designed for optimum performance when used with the SN75172 or SN75174 quadruple differential line drivers.
The SN65175 is characterized for operation from −40°C to 85°C. The SN75175 is characterized for operation from 0°C to 70°C.
Similar products you might be interested in
Compare alternates
Pin-for-pin with same functionality to the compared device
Technical documentation
No results found. Please clear your search and try again.
View all 1Type | Title | Date | ||
---|---|---|---|---|
* | Data sheet | SNx5175 Quadruple Differential Line Receivers datasheet (Rev. D) | PDF | HTML | 16 Oct 2023 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Simulation model
SN75175 IBIS Model
SCEM495.ZIP (13 KB) - IBIS Model
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Simulation tool
TINA-TI — SPICE-based analog simulation program
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
User guide: PDF
Package | Pins | Download |
---|---|---|
PDIP (N) | 16 | View options |
SOIC (D) | 16 | View options |
SOP (NS) | 16 | View options |
TI's Standard Terms and Conditions for Evaluation Items apply.
Ordering & quality
Add a quantity to your cart and begin the checkout process to view the options available to select lot or date codes from existing inventory.
Learn more
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.
Video series
View all videos